Driveways & Concrete
Patios and alfresco slabs: getting the levels right against the house
Precision Plumbing & Concreting ·
A patio can look neatly aligned with the living room yet create problems if its finished surface sits too high against the house. Door sills, brickwork weep holes, cladding clearances and drainage outlets all influence the usable level, often before the concrete finish is chosen. On the Mornington Peninsula, an alfresco roof also needs to be considered alongside wind-driven rain and water arriving from adjoining paths or gardens. The aim is not simply to make everything flush: it is to create a practical outdoor space without compromising the building’s moisture protection. This Precision Plumbing & Concreting guide explains what to have measured, which details need coordinated design, and what to resolve before the slab is booked.
Set the patio height from the doorway detail
Ask for a level survey that records internal floor height, the door sill, existing outdoor surfaces and proposed drainage points against one reference. The top of the visible threshold is not automatically the correct concrete height. Sliding-door tracks, sill drainage openings and the door manufacturer’s installation requirements must remain functional.
If you want a near-level transition, raise that requirement before accepting a slab layout. It may need a coordinated threshold, waterproofing and drainage detail rather than simply lifting the concrete. Include any future tiles or paving in the finished-height calculation. Where a step is proposed, have its dimensions and relationship to the landing checked, rather than leaving an awkward last-minute change at the doorway.
Keep the wall’s moisture defences exposed
Walk the full house-facing edge with the contractor and identify brick weep holes, damp-proof courses, flashing, cladding edges and any required termite inspection zones. Mark these on the proposed level drawing. Raising a patio can obstruct drainage from a brick cavity or bridge moisture protection, even when the door itself still opens comfortably.
Do not treat a bead of sealant as a substitute for the required wall clearance. Ask the designer or building surveyor to establish the applicable separation for the actual wall system and exposure. Existing render, garden beds or old paving may conceal important details; arrange assessment before the new height is locked in. An older surface is not proof that its level was suitable.
Treat roofed and open areas as different wet zones
A covered alfresco still receives wind-blown rain, splash and cleaning water. Show the roof edge, downpipes and exposed patio extension on the same plan. Water from the open section should not be directed back through the sheltered dining area or towards the house. The surface grades need to suit the layout, finish and collection system, not a generic fall applied everywhere.
Confirm whether a roof, verandah or pergola forms part of this project or a later stage. Mornington Peninsula Shire lists these structures among work commonly requiring building permits. Engage a private building surveyor to establish requirements before building work starts; the Shire does not issue building permits. Check planning requirements separately, and coordinate any future roof supports with the slab design now.
Give collected water a lawful destination
A drain beside the doors is useful only when its position, capacity and outlet work together. Ask where surface water travels during normal rainfall and where excess water would go if a grate becomes obstructed. Keep grates accessible for cleaning, and avoid layouts where furniture, outdoor kitchen cabinetry or a narrow wall gap prevents maintenance.
Confirm the property-specific legal point of discharge through Mornington Peninsula Shire. A nearby pit does not automatically authorise a connection, and separate approvals apply to road or drainage works. Have existing pipe routes and suitability assessed rather than assuming an old downpipe connection can accept the patio runoff. Our stormwater drainage information can help you frame the drainage scope alongside the concrete work.
Allow the patio and house to move independently
Do not assume the patio should be rigidly attached to the house slab. The junction needs a designed movement detail that accounts for the building, the new concrete and moisture protection. Ask how isolation and other joints will be arranged around walls, columns and changes in shape, including how any tiled finish will accommodate those joints.
Uniform prepared support matters, but soil behaviour cannot be inferred from a Peninsula suburb name. Previous filling, disturbed ground and drainage history need site assessment. Loading from masonry barbecues, roof posts or other substantial features must be declared for project design. CCAA guidance supports coordinated support, specification and jointing; its housing guide is historical guidance, not current regulatory authority. Discuss these requirements when defining your concreting scope.
Approve one coordinated level plan before pouring
Request a drawing showing finished concrete heights, surface-flow directions, door transitions, wall clearances, drains and joints. Include the thickness of any later surface finish. Make responsibility clear for threshold detailing, drainage connections and checking levels before placement. Choosing a texture for wet outdoor use also matters, but texture cannot compensate for ponding or a poorly resolved doorway.
Check the patio’s connections to side paths and the driveway so solving one level does not create a low pocket elsewhere. If driveway renewal is also planned, coordinate both projects before fixing heights. Keep the agreed drawing with the quotation so changes can be assessed against the whole layout.
Frequently asked questions
Can my alfresco concrete finish flush with the indoor floor?
Sometimes, but it requires a compatible doorway, moisture-protection and drainage detail. Have the transition designed before setting slab heights; matching floor levels alone is not enough.
Can a strip drain replace clearance below weep holes?
No. A drain collects surface water; it does not replace the wall system’s required clearances or cavity drainage. Both details need to work independently.
Should I allow for outdoor tiles even if they come later?
Yes. Give the designer the proposed tile and bedding build-up so finished levels, sill clearance, drainage and movement joints account for the completed surface.
What should I bring to an initial site discussion?
Bring available house plans, door details and your proposed roof or kitchen layout. Point out existing ponding and show where paths or driveway works may connect.
Sources
Call 0421 992 400 or get a quick estimate for your project.
Quick estimate